ajuda no router bthub3 wtgh

[msg]

Ei fiz isso entao deve ser do meu windons7. E a porta 25000 e a 19000. Obrigado

 

[Fonsec@]

Ei fiz isso entao deve ser do meu windons7. E a porta 25000 e a 19000. Obrigado

Mas já conseguiste abrir a porta ou não?

 

[msg]

nao a 25000 e 19000 nao eu mando esta fotos. Eu ainda nao abri portas mando esta fotos para veres como esta

 

[Fonsec@]

Não podes mexer no Port Triggering, são coisas diferentes e talvez esteja ai o problema, limpa isso.

 

[msg]

ola

eu tenho esta material. A caixa branca e da fibra optica sera isto que esta a nao deixar abrir. Obrigado

 

[msg]

sinceramente ja nao sei o que fazer mais. Obrigado

 

[Fonsec@]

A caixa branca é o modem e não deveria impedir-te de abrir as portas, eu também tenho um modem antes do router e não tenho problemas em abrir as portas.

Faz um reset ao router e começa tudo de novo e não te esqueças só fazes o Port Forwarding e colocas o teu DNS.

 

[msg]

A caixa branca é o modem e não deveria impedir-te de abrir as portas, eu também tenho um modem antes do router e não tenho problemas em abrir as portas.

Faz um reset ao router e começa tudo de novo e não te esqueças só fazes o Port Forwarding e colocas o teu DNS.

estive aqui com um amigo e fizemos tudo e nao deu. Ele pensa que pode ser da dreambox eu tenho uma 8000hd com uma imagem newnigma e na 800hd se tenho esta sat4fun. Sabes como configuara as dreambox ou quando a gente mete a imagem fica logo tudo configurado. Obrigado

 

[msg]

Ja abriu e esta a trabalhar 5 estrlas eu amanha ja meto aqui como e que se resolveu. Foi meu filho que fez e ele saiu e so o vejo amanha.

 

[msg]

Ola e muito obrigado a todos. Eu ja resolvi isto, as portas ja abrem. Como e que fiz.Foi, eu tinha todo bem configurado
so que no TCP/UDP/ANY eu escolhia o ANY porque era assim que eu li em foruns e vi no youtube. Por isso na tentava outra
opcoes e se o fiz nao me lembro. O meu filho pega no seu Aplle e configurou as portas TCP/UDP e abriu logo.
Muito obrigado e ja agora o router e um ( BT HOme HUB 3).

 

[msg]

Ola pessoal. Nao sei o que se passou mas a porta fechou e eu ja fiz as mesmas configuracoes e nao abrem. Telefonei ao gajos da bt e eles dizem que e da box. Algum entendido em box 8000hd e 800hd se clones que me possam dizer o que esta mal. Muito obrigado

 

[Fonsec@]

As box não abrem nem fecham portas dos routers, estranho esse teu problema, como disse anteriormente já fui cliente da BT e nunca tive qualquer problema com os routers.

 

[msg]

Pois e , estive ontem a falar com eles e depois mandaram me para outro departamento, e se ele resolvessem o problema eu tinha que pagar. Mas mesmo assim nao resolveram o problema. Disseram que era da dreambox. Eu tenho os setings da cccam 2.2.1 assim. esta alguma coisa mal? Obrigado

######################################################################
# Other config settings #
######################################################################
# server shall listen on this port pro incoming connections
# default port is 12000, disable server with parm -s or set port 0
#
#SERVER LISTEN PORT : 19000

# server can give some info about server and client connections
# and cardinfo using telnet or webbrowser.
#
# Switch on/off access to info
# default is yes
#
#ALLOW TELNETINFO: no
#ALLOW WEBINFO: no

# Show extended client info when showing client list
# default is yes
#
#SHOW EXTENEDED CLIENT INFO : no

# The webinfo service can be protected with a username and password.
# This is switched off by default
#
#WEBINFO USERNAME : <username>
#WEBINFO PASSWORD : <password>

# The telnetinfo service can be protected with a username and password.
# This is switched off by default
#
#TELNETINFO USERNAME : <username>
#TELNETINFO PASSWORD : <password>

# default port for telnet is 16000
# default port for web is 16001
# supported commands:
# info
# activeclients
# clients
# servers
# shares
# providers
# entitlements
# example use:
# echo servers | telnet localhost 16000
# go with your browser to http://ip_CCcam_server:16001
#
#TELNETINFO LISTEN PORT : 16000
#WEBINFO LISTEN PORT : 16001

# time in seconds to keep On Screen Display active.
# default is 0 (turned off)
#
#ZAP OSD TIME : 3

# username used to show popup (default : root)
#OSD USERNAME : root

# password used to show popup (default : dreambox)
#OSD PASSWORD : dreambox

# port used to show popup (default : 80)
#OSD PORT : 80

# Serial reader config. Add as many as you have attached too your system
# replaces old name 'PHOENIX READER PATH', but still works.
# default is none
# optionally add readertype : phoenix,mouse,uniprog,sc8in1,smartreader+
# (when non readertype given defaults to uniprog (e.g. for mastera))
#
# SERIAL READER : <device> <type>
#
# example
#
#SERIAL READER : /dev/tts/0

# Serial reader smartcard write delay.
# Setting to finetune smartcard write speed, optimal setting depends on speed of system, and
# speed of card. Default value is calculated, but can overrule by setting.
# Use number of microseconds delay between bytes, 0 = no delay, -1 = calculated default
# Note: huge difference between values 0 and 1, because of schedular overhead
#
# SMARTCARD WRITE DELAY : <device> <delay>
#
# example, 10ms write delay on smartcard in reader attached to /dev/ttyUSB0
#
#SMARTCARD WRITE DELAY: /dev/ttyUSB0 10000
#
# NOTE on sc8in1; because 8 smartcards are used on the same devicename, use
# devicename_0 .. devicename_7 for settings which require devicename to make
# settings per smartcard. example /dev/ttyS0_0, /dev/ttyS0_1 ..
# example, 8ms write delay between bytes to smartcard on last sc8in1 channel, attached to /dev/tts/0
#
#SMARTCARD WRITE DELAY: /dev/tts/0_7 8000

# Smartcard clock speed override
# Setting override specified speed for smartcard.
# Don't add setting unless you're sure what you're doing.
# In 99% of the cases the reader selects the optimal speed.
# Adding this setting either slows your card down, or might destroy it.
#
# SMARTCARD CLOCK FREQUENCY : <device> <freq>
#
# example
#
#SMARTCARD CLOCK FREQUENCY: /dev/ttyUSB0 5500000

# if timing should be shown in OSD and debug output
# default is no (turned off)
#
#SHOW TIMING : yes

# enables mini OSD which shows server(type), cardreader, keys or fta only
# default is no (turned off)
#
#MINI OSD : yes

# turns debugging on and off
# default is no (turned off)
#
#DEBUG : yes


# should CCcam try to read and parse newcamd.conf for server connections
# default is no (turned off)
#
#NEWCAMD CONF : yes


# configure what EMM blocker you want. Add as many as readers you have attached
# default is blocking nothing
#
# B: /dev/sci0 01
# 00 - nothing
# 01 - sa blocked
# 02 - ua blocked
# 04 - ga blocked
# and sum of for combinations
#
#examples
#
#B: /dev/tts/0 07
#B: /dev/sci0 01

# disable all local EMM readers
# saves lots of CPU, but you won't get any updates anymore
# (unless you get updates from your clients)
#
# default: no
#
#DISABLE EMM : yes

# with this setting you can
# allow a client on two hops away
# to send the updates to the cardserver
#
# default : no
#
#EXTRA EMM LEVEL : yes

# with this setting you can
# configure how many emm listeners are started.
# for example use 2 when recording
# and viewing different systems and both need constant updates
#
# default : 1
#
#EMM THREADS : 1

# overrule the nds boxkey (4 byte hex)
#
# BOXKEY: <device> <byte1> <byte2> <byte3> <byte4>
#
#example
#
#BOXKEY: /dev/sci0 00 11 22 33

# set card pin
# * please be very careful with this option as you could lock your card *
#
# PIN: <device> <pin>
#
#example
#
#PIN: /dev/sci0 1234

# overrule the irdeto camkey (8 byte hex), default 11 22 33 44 55 66 77 88
#
# CAMKEY: <device> <byte1> <byte2> <byte3> <byte4> <byte5> <byte6> <byte7> <byte8>
#
#example
#
#CAMKEY: /dev/sci0 11 22 33 44 55 66 77 88

# overrule the irdeto camdata (64 byte hex)
# trailing zero bytes can be omitted
# default for unknown ASC's is 11 22 33 44 55 66 77 88 00 00 .. 00, known ASC's have other defaults
#
# CAMDATA: <device> <byte1> <byte2> <byte3> <byte4> <byte5> <byte6> ... <byte64>
#
#example, when only the first 15 camdata bytes are nonzero
#
#CAMDATA: /dev/sci0 11 22 33 44 55 66 77 88 99 aa bb cc dd ee ff

# custom add id's for BEEF patched cards
#
# BEEF ID: <ident1> <ident2> <ident3> <ident4> <ident5> <ident6> <ident7> <ident8> <device>
#
#example
#
#BEEF ID: 4101 0 0 0 0 0 0 0 /dev/sci0

# what Softcam.Key should CCcam try to read
# defaults to /var/keys/SoftCam.Key
#
#SOFTKEY FILE : /var/keys/SoftCam.Key


# what AutoRoll.Key should CCcam try to read
# defaults to /var/keys/AutoRoll.Key
#
#AUTOROLL FILE : /var/keys/AutoRoll.Key


# what constant.cw should CCcam try to read
# defaults to /var/keys/constant.cw
# file content can be like
#
# ca4:id6:sid4mtpid4:ecmpid4:key16(01 02 03...)
#
#STATIC CW FILE : /var/keys/constant.cw


# in this file you can configure what CAIDs CCcam should prefer or ignore
# defaults to /var/etc/CCcam.prio
# file content can have ignores (I) and prio lists (P)
#
# note 1: I line affects both for ecm and emm (receive no emm on ignored systems)
# P line only affects ecm choice (emm still received for all available systems, not just the priority system)
#
# note 2: ident 0 means 'all idents'. So 'caid:0' is the same as 'caid'.
#
# note 3: for some systems (e.g. nagra (caid 18xx)), the ident is not known at the time the
# prio lists are checked. In that case, matching is done on caid only, even if the P line
# defines nonzero idents. So for example '1801:401' behaves the same as '1801' in a P line
# I lines work differently, they are checked two times, once before ecm or emm is received, again
# after ecm or emm are received (and nagra ident should be known)
# P lines are only checked once, before ecm received.
#
# note 4: if a P line contains caid:ident pairs which are not available for the current
# channel, that P line is not used for that channel.
# Example, channel has systems 626, 1801:401 then P line with "1801,100:96,626" is ignored by that channel,
# because channel doesn't have 100:96.
# But P line with "1801" works, and also "626,1801" will work for channel
#
# note 5: P lines are parsed in the order in which they are found in the prio file.
# Only the first matching P line is used
#
# situation 1: ignore allways this caid, all idents, on all channels
# I: caid
#
# situation 2: ignore allways this caid/ident pair
# I: caid:ident
#
# situation 3: ignore this caid/ident pair, on channel 'sid'
# I: caid:ident:sid
#
# situation 4: when both caid1 and caid2 exist for a channel, prefer caid1 over caid2
# P: caid1, caid2
#
# situation 5: when caid1:ident1 till caidN:identN exist for a channel, use them in order of this list.
# P: caid1:ident1, caid2:ident2, .., caidN:identN
#
# situation 6: when caid1:ident1 till caidN:identN exist for channel 'sid', use them in order of this list.
# Sid on first caid/ident pair identifies sid for which list is used. All other sids ignore this list.
# P: caid1:ident1:sid, caid2:ident2, .., caidN:identN
#
#CAID PRIO FILE : /var/etc/CCcam.prio

#
# In this file all provider idents are defined
# The info from this file is being used in the web interface
# format:
# <caid><ident> "Provider description"
#
# PROVIDERINFO FILE : /var/etc/CCcam.providers

#
# In this file all channel idents are defined
# The info from this file is being used in the web interface
# format:
# caid:ident:sid "Channel description"
#
# CHANNELINFO FILE : /var/etc/CCcam.channelinfo

# write wrong logins to file
# defaults is off
#
#LOG WARNINGS : /tmp/warnings.txt

# global setting for stealthy login to newcamd/newcs server, N line can overrule
# stealth modes: 0 = disabled, 1 = mgcamd new, 2 = mgcamd old, 3 = evocamd, 4 = generic
# default: 0
#
#NEWCAMD STEALTH : 0

# load balancing between identical cards, list device names of card readers containing identical cards,
# optionally followed by a list of service id's which are to be excluded from loadbalancing
#
# LOADBALANCE : <device1> <device2> .. <devicen> { <exceptsid1>, <exceptsid2> .. , <exceptsidn> }
#
# multiple loadbalance groups can be configured, by adding multiple lines
# warning: restart is required, when loadbalance group config changes
#
#example 1: load balance requests for three identical cards
#
# LOADBALANCE : /dev/ttyS0 /dev/ttyS1 /dev/ttyS2
#
#example 2: load balance requests for two almost identical cards, sid 0df3 and 0de1 are only available
#on one of the cards, so requests for these sids shouldn't be loadbalanced
#
# LOADBALANCE : /dev/ttyS5 /dev/ttyS6 { 0df3,0de1 }

# in version 1.2.1 and lower there was a problem which could lead to disconnecting clients
# in version 1.4.0 network load was significantly reduced
# in version 1.7.0 dangerous password bug was fixed
# in order to take advantage of these fixes, all clients should upgrade
# with this setting you can force that clients at least use a certain version otherwise they are denied when logging in
#
# default : accept all versions
#
#example 1: avoid disconnecting clients problem
#
#MINIMUM CLIENT VERSION : 1.3.0
#
#example 2: achieve network load decrease
#
#MINIMUM CLIENT VERSION : 1.4.0
#
#example 3: don't allow potentially wrong passwords (pre 1.7.0 has password bug)
#
#MINIMUM CLIENT VERSION : 1.7.0


# Irdeto smartcards: option to disable smart chid checking for irdeto smartcards.
# Default, only chids advertised by card are accepted.
# This avoids a lot of unwanted card traffic
#
# But if smartcard has hidden/unknown chids, all chids should be tried.
# In that case specify 'TRY ALL CHIDS' option for cardreader.
# Use with care, enabling option causes more card traffic.
# Only use setting when some channels don't work without it.
# note: if even this setting don't help decode all channels, try using
# commandline arg -l, to disable all self-learning features (warning: slower)
#
#TRY ALL CHIDS : <device>
#
#example: card in /dev/ttyUSB0 gets ecm for all possible chids, not
#just the chids it officially supports
#
#TRY ALL CHIDS : /dev/ttyUSB0

# perform smartcard post init commands
#
# POSTINIT : <device> <filename> (<autodelete>)
#
# send commands in 'filename' to 'device', and delete 'filename' when
# optional 'autodelete' argument nonzero
#
#example:
#
#POSTINIT : /dev/sci0 /tmp/postinit
#
#example /tmp/postinit contents:
#c134000003000000
#c13201000a

# Option to override autodetected dvb api version. Restart needed.
#
#DVB API: <value>
#
# <value> -1 = no dvb, 1 = dvb api 1, 3 = dvb api 3
#
# WARNING: only use when autodetect fails!
#
#example, disable nonworking dvb hardware:
#DVB API: -1

# Option to set global share limits
#
#GLOBAL LIMITS: { caid:iddownhops), caid:iddownhops), ... }
#
#example:
#
#GLOBAL LIMITS : { 0100:000080, 0622:000000:1, 0500:000000:2 }
#
# all users get no 0100:000080.
# and our 0622:000000 cards only for themself (1 hop down),
# and 0500 cards for themself plus one additional hop down.
# global limits are overridden by client specific limits (see F

# Option to reject shares with less than required downhops on clientside
#
#MINIMUM DOWNHOPS: <value>
#
# default: 0 (don't ignore any shares)
#
#example:
#
#MINIMUM DOWNHOPS: 1
#
# ignore shares that have less than 1 'downhops' (i.e. can not be shared
# further down to other clients)

# Option to ignore all shares that go through a certain node
#
#IGNORE NODE: <nodeid>
#
#example, ignore two nodes:
#
#IGNORE NODE: ccd536ab515767ad
#IGNORE NODE: aad536ab515761af


# The seca handler is used to better support simulcrypt on the same ident
#
# With this setting you can change the behaviour of how SECA has to be used
# This setting is ignored unless SECA2/SECA3 simulcrypt is detected!!
#
# When disabled CCcam behaves like previous versions
#
# When "prefer SECA3 over SECA2" is enabled try to use SECA3 ecm first, then SECA2
#
# When "Ignore SECA2" is enabled, ignore all SECA2 ecm so a SECA3 card will not get SECA2 request which it cannot handle
#
# When "Ignore SECA3" is enabled, ignore all SECA3 ecm so a SECA2 card will not get SECA3 request which it cannot handle
#
#
# The following settings can be used
#
# SECA HANDLER: <value>
# <value> : 0 = disabled, 1 = prefer SECA3 over SECA2, 2 = prefer SECA2 over SECA3, 3 = Ignore SECA2, 4 = Ignore SECA3
#
# default: 1
#
# Example try to use SECA3 ecm first, then SECA2
#SECA HANDLER: 1
#
# Example try to use SECA2 ecm first, then SECA3
#SECA HANDLER: 2
#
# Example to ignore all SECA2 ecm so a SECA3 card will not get SECA2 request which it cannot handle
#SECA HANDLER: 3
#
# Example to ignore all SECA3 ecm so a SECA2 card will not get SECA3 request which it cannot handle
#SECA HANDLER: 4


# Configure limited list of accepted sids for smartcard
# When omitted, all sids are allowed.
# (can work together with LOADBALANCE configuration, or for standalone cards)
#
# SMARTCARD SID ASSIGN : <device> <maxnumberofsids> { <sid1>, <sid2>, ... <sidn> }
#
# <device> is the reader devicenode
# <maxnumberofsids> limits the total number of sids assigned to the card (0 = use length of sid list)
# { <sid1>..<sidn> } lists the sids that are assigned to the smartcard, when omitted, <maxnumberofsids> is used to auto assign sids
#
# when <maxnumberofsids> is larger than the length of the sidlist, the remainder of the sids are auto assigned, till the list reaches <maxnumberofsids>
# Check entitlement output for realtime assignment list
#
# WARNING: when SMARTCARD SID ASSIGN config changes, restart is required before settings take effect
#
#example1: smartcard in device /dev/ttyUSB0 only handles requests for sids df3, df4, df5
#
# SMARTCARD SID ASSIGN : /dev/ttyUSB0 0 { 0df3,0df4,0df5 }
#
#example2: smartcard in device /dev/ttyUSB0 handles requests for max 5 sids, auto assigned in the order of occurance. A request for a 6th sid will be denied.
#
# SMARTCARD SID ASSIGN : /dev/ttyUSB0 5
#
#example3: smartcard in device /dev/ttyUSB0 handles requests for max 5 sids, 3 of which are df3, df4, df5, remaining 2 are auto assigned
#
# SMARTCARD SID ASSIGN : /dev/ttyUSB0 5 { 0df3,0df4,0df5 }

 

[florindo]

SERVER LISTEN PORT : 19000

Amigo, tens meter aí a porta, se não for essa... e não pode estar comentada.

Neste caso tens que retirar o cardinal.

 

[msg]

Agora esta assim
# Other config settings #
######################################################################
# server shall listen on this port pro incoming connections
# default port is 12000, disable server with parm -s or set port 0
#
SERVER LISTEN PORT : 19000

# server can give some info about server and client connections
# and cardinfo using telnet or webbrowser.
#
# Switch on/off access to info
# default is yes
#
#ALLOW TELNETINFO: no
#ALLOW WEBINFO: no
Dizes nao pode esta comentada. Era so tirar o # ou e mais alguma coisa. A porta e essa. Muito obrigado

 

[msg]

Ola amigos. Muito obrigado mas eu ja resolvi o problema. E com uma dica do Florindo # eu foi la. Meti a cccam 2.3.0 e alterei as configuracoes e abriu logo a porta, Agora gostava de mudar o username e pass da dreambox alguem sabe como. Muito obrigado

 

[florindo]

Ola amigos. Muito obrigado mas eu ja resolvi o problema. E com uma dica do Florindo # eu foi la. Meti a cccam 2.3.0 e alterei as configuracoes e abriu logo a porta, Agora gostava de mudar o username e pass da dreambox alguem sabe como. Muito obrigado

Amigo, faz assim, abres o DCC, procuras por telnet, depois escreves passwd, e fazes enter.

Metes a pass que entenderes... fazes enter de novo, repetes a pass e enter de novo, e fica feito!

Amigo, só um aparte... o teu problema não era o router como se comprovou... mas sim o config da CCCam.

 

[msg]

Exactamente. Sabes isto quando um gajo nao sabe f..... ate os c.... atrapalham. Come eu ainda ando a aprender eu pensava que era so meter a cccam que ela ja estava com as configuraçoes feitas e afinal nao. Ela tem la tanta coisa escita que se calhar nao e la precisa mas eu como nao tenho a certeza deixo estar. Muito obrigado a todos